Many private households have an old LPG bottle. Many useful things can be made from this object, for example, a simple heating device.
If there is a desire and a welding machine, then a potbelly stove from a gas cylinder with your own hands can be made without any problems. Of course, some additional materials will be needed.
The principle of operation of the stove-potbelly stove
A potbelly stove is a primitive version of a metal wood stove. Such a device works extremely simply: firewood is laid in the furnace, they burn, the furnace body heats up and gives off heat to the surrounding air. Smoky gases are removed through the chimney, and ash is poured through the grate to the ash pan, which should be periodically cleaned.
One of the main advantages of a potbelly stove is its simplicity of design. There are no strict sizes, the main thing is that the casing withstands heat and the chimney works properly. An experienced master will make such a stove in just a couple of hours. And you can burn almost any dry tree in it: both logs and sawdust. On our site there is an article with a detailed description of the process of making a potbelly stove with your own hands.
They also heat a potbelly stove with other combustible materials: diesel fuel, coal, peat, household waste, etc. If desired, you can cook quite successfully on such a stove. This point should be considered even before the start of the manufacture of the structure in order to make a smooth cooking surface.
The potbelly stove is a thick metal combustion chamber with a loading door, a chimney, a grate and a blower. As the case, you can use the old gas cylinder
But it should be reckoned with the disadvantages of such a heating solution. For starters, this is a high risk of burns and fires.
For a potbelly stove, you need to choose a special place, trimmed with fire-resistant materials. It is advisable that she stand on the side where no one accidentally touches the body and burns herself.
If desired, the upper part of the vertical potbelly stove from an old gas cylinder can be turned into a hob of modest size
Such a metal construction weighs a lot, so there is no question of any mobility of the device. Moving a potbelly stove to heat different rooms will be difficult.
Utility rooms, in which there is no electric power or where it is intermittently supplied, such as a garage, a barn, a workshop, etc., are usually heated with such stoves.
Of the two gas cylinders connected perpendicularly, you can make an improved version of the potbelly stove, which allows you to save more heat and get high returns when burning fuel
Another problem is the low efficiency, since part of the thermal energy during the combustion of wood literally flies out into the chimney. There are various ways to retain heat and modify the potbelly stove a little to make it work more efficiently.
Finally, you need to take care of the good ventilation of the room in which the potbelly stove is installed, since such a device burns a large amount of oxygen during operation.
So, the potbelly stove consists of a metal case, the role of which is usually “invited” to the old gas cylinder. In the case it is necessary to make two doors: large and small. The first serves to load fuel, the second is needed as a blower, through which air enters from the combustion chamber to ensure the combustion process and traction.
The drawing of a stove-potbelly stove from a gas cylinder allows you to make a device with specific parameters and calculated power, but such accuracy is not required
At the bottom, at some distance from the bottom of the structure, the grate should be welded. It can be made of thick wire or just take a sheet of thick metal and cut long slits in it. The distance between the bars of the grate should be such that the flue material does not wake up in the ash pan.
If the potbelly stove is heated only with wood, the grate of the grate is made large, but when it is supposed to use wood chips, the grate should be made more frequent.
A curved metal chimney mounted on a potbelly stove from a gas cylinder allows you to keep more heat in the room and increase the efficiency of the structure
The ash box can be welded from sheet metal or you can take a finished metal container of a suitable size and resistant to strong heat. Some people prefer to dispense with an ashpit altogether; they simply remove ash from the lower section as necessary, although this is not very convenient. Typically, a chimney for a stove is brought up to provide the necessary traction.
The standard design of the gas cylinder stove can be improved by increasing productivity, turning a solid fuel heater into a heater or hob:
Image Gallery
Photo from
Fixed on the body
Mounting to a cylinder of heating pipes
Air heating unit
Food Warmers
Manufacturing Recommendations
A potbelly stove from a cylinder can be different: the container can be placed horizontally or vertically. You need to choose a case of suitable size, and then use it correctly.
You will need a sheet of steel that is resistant to prolonged heating, a thick wire for the grate, a corner for the legs, etc. In the manufacturing process, a number of nuances should be taken into account to make the stove convenient and efficient.
Stage No. 1 - selection and preparation of the cylinder
Gas cylinders are very different. For potbelly stoves, a container for liquefied gas of 50 or 40 liters is best suited. If you need a small oven, you can take a cylinder of 12 or 27 liters.
But this will be a device for heating small utility rooms. Similar containers of five liters are practically useless. Such a small potbelly stove will heat up quickly, but will soon cool down, so the heating effect from it will be very insignificant.
An interesting option for a home-made potbelly stove is a freon container. Such a cylinder has thick walls and an elongated body. The container must be cut so that the body length is about 70 cm. Thick walls, of course, make the structure heavier, but they retain heat better. The potbelly stove will heat up for a long time, but at the same time it will warm longer.
Before starting work, it is necessary to properly prepare the gas cylinder: remove the remaining gas from it, drain the condensate and fill the tank with water, which can then be poured
When the cylinder is selected, you need to prepare the welding machine and remember the safety rules. Even in a very old cylinder there are always some remnants of combustible gas. If you immediately start cutting it by welding, a life-threatening explosion is almost guaranteed. For those who have not yet used a welding machine, we recommend reading this article.
To begin with, it is recommended to open the cylinder and vent the remaining gas. Of course, this should be done on the street, and not indoors. Then you need to drain the remaining liquid condensed inside from the balloon. This substance usually has a pungent and unpleasant odor, so it’s best to prepare a small container with a lid for it in order to immediately pack it and discard it.
The design of the stove potbelly stove does not have particularly stringent requirements for the parameters. The larger the combustion chamber, the more spacious the room can heat the unit
If condensation is accidentally spilled on the floor of a room, a specific aroma may persist for a very long time. After all these operations, the cylinder is still not ready for contact with the welding machine, because the residual gas vapor remains inside.
It is necessary to fill the cylinder with water to the very top in order to completely displace all gas from it. After this, the water is drained, now the cylinder can be cut without problems.
Stage No. 2 - production and filling of the body
Next, you need to choose the type of potbelly stove from the cylinder, whether the cylindrical body will be located horizontally or vertically.
Image Gallery
Photo from
Horizontally-mounted stove body
Advantages of loading firewood in a horizontal case
Minimum space for installing the oven
Portable potbelly stove from a mini balloon
All other operations are carried out taking into account this orientation. If a horizontal position is selected, then one of the ends of the cylinder will serve as the back wall, and on the other you need to install a loading door and a blower.
If you plan to make a vertical potbelly stove from a gas cylinder, you will need to make two holes: for loading fuel and for blowing with an ash pan
A thick reinforcing wire can be used for the grate. In order not to cook the grate from it, you can bend it with a frequent zigzag, “snake”. This design is welded to the inner walls of the metal casing.
The front wall is made of metal sheet as follows:
- Metal needs to be applied to the front of the stove to mark it.
- According to the marking, a round part should be cut.
- Put another marking on it: for a rectangular door and a blower.
- Cut holes according to the marking.
- Make doors.
- Weld hinges, locks to the front wall and hang the doors.
- Weld the wall with doors to the body.
Both doors should be sealed with an asbestos-cement cord along the contour so that they fit snugly against the body. The back wall in such a stove is usually not necessary; its role is played by the bottom of the cylinder. In the upper part of the body, close to the back wall, you need to make a hole for the chimney.
The pipe must be taken from thick metal, since the lower part of the chimney will come into contact with heated flue gases. Thin metal in this place will quickly burn out. Now, solid legs of reinforcement, pieces of metal or pieces of a metal corner are welded to the bottom of the stove. They must withstand both the weight of the structure itself and the fuel that will be loaded into it.
About the same technology is used to make a vertical potbelly stove from a balloon. The bottom of the container will become the lower part of the structure, at the top you need to make a cylindrical “roof” with a hole for the chimney. Usually the top of the balloon is cut off. At the end of the installation, it will be possible to weld it back. Doors - for loading and blowing - are made in front of the cylinder body.
Such a potbelly stove will take up less space than the horizontal version, and it will also be higher. If it is supposed not only to heat the room, but also to cook food, then it will be necessary to adjust the height of the stove taking into account this moment and ensure a smooth cooking surface.
But usually the diameter of the container is not large enough to provide a full cooking opportunity. Although boiling the kettle is a doable task.
This drawing allows you to get an idea about the arrangement of a horizontal version of a potbelly stove from a cylinder, to the bottom of which a ash box is attached
The grate can be made in the same way as described above: from reinforcement bent by a snake along the diameter of the pipe. It is welded between the holes for loading and blowing.
Some are trying to reduce the amount of welding work, leaving the top of the tank almost untouched. But then all other work will be more difficult.
In a horizontal potbelly stove you can not weld a grate, but turn into it a part of the body by drilling holes of a suitable diameter and attaching an ash box from below
For example, the grate will have to be inserted not from above, but pushed into the furnace door and somehow held in the correct position. Now you need to make doors with hinges and locks and weld them to the body of the potbelly stove, previously sealing with an asbestos-cement cord. It remains to install a chimney at the top, and weld the legs below.
Stage 3 - manufacture of a door and an ash pan
Doors for potbelly stoves can be made from those parts of the body that remain after cutting holes. Hinges and latches are welded to them. These are simple elements. Loops can even be made from links in a thick chain. The second, more expensive option is the purchase of finished cast metal structures.
To install a finished molded door on a makeshift stove, a frame from a metal corner should be welded to the loading hole
Two separate doors can be selected: large for the feed opening and narrow for the blower. But there are also sets in which such doors are combined into a single design.
The holes for such doors must be cut exactly to size. After that, you need to weld the frame from the corner to the edges of the openings.
Several links of a thick chain, similar to a bicycle, can be used as hinges for a makeshift stove-made door made of a cylinder
The frame of cast doors is attached to the resulting frame using bolts. It is recommended to pre-weld a small side so that there are no cracks, and the furnace closes tightly.
In small potbelly stoves, you can completely dispense with the grate even if you wish.
On the left is an inverted case of a horizontal potbelly stove with an ash pan welded to it, and on the right is a general view. The ash pan is put forward to regulate the flow of oxygen, it is not necessary to do blowing in such a model
It is difficult to find a place for it if you make a stove of small size or low, for example, a horizontal option. In such a device, no blowing is done, air is provided with the help of a loading door, which is simply ajar. It is easy to make grate from the armature, but they are not particularly reliable.
Over time, the valve burns out, it has to be replaced. An alternative could be a piece of sheet metal in which slits or openings of a round shape are cut. To collect ash, you can use a special box - an ash pan.
In the horizontal version, stoves from the cylinder can be installed in the lower part complete with an ash pan, since the lower part of the body will have to be cut to facilitate installation.
Step-by-step photo guide
To make a home-made stove, you will need one annealed empty gas cylinder, a Ø 108 mm pipe for a chimney (the meter depends on specific specifications), trimming a steel strip and corner, three hinges for hanging doors.
The construction of the body of the future stove is carried out in the following sequence:
Image Gallery
Photo from
Step 1: Cutting the chimney hole
Step 2: Marking the doors of the ash pan and firebox
Step 3: Cutting the cylinder body according to the marking
Step 4: Stripping Deburring Burrs
Step 5: Assembly of the grate blank
Step 6: Drawing the outline of the grate
Step 7: Trimming the grate
Step 8: Fixing the grate inside the housing
The stove-potbelly stove from an empty gas cylinder is almost ready: the finishing touches remain:
Image Gallery
Photo from
Step 9: Fixing the flue pipe
Step 10: Fixing the hinges and hanging the doors
Step 11: Preassemble the Chimney
Step 12: Assembling the chimney and starting the stove
The height of the chimney depends on the shape of the roof and the presence of a number of objects that can interfere with traction. It should be at least 0.5 m above the flat and low pitched roof. If there are tall trees or buildings nearby, then the mouth of the pipe must be arranged above them.
How to increase efficiency?
To make a potbelly stove work more efficient, there are several simple ways.First, you should insulate the chimney to save some of the heat that goes with the flue gases. Various methods can be used to increase the contact area of the heated metal with the surrounding air.
The device of a kind of cap from an additional gas cylinder will help to significantly increase the thermotechnical qualities of a potbelly stove built from a gas cylinder:
Image Gallery
Photo from
Conventional cylinder stove in the garage
Preparation of a cylinder of a smaller displacement
Installing a chimney chamber
Device for increasing heat transfer
Some masters recommend making the chimney not strictly vertical, but curved. This will increase the path of the passage of combustion waste and allow part of their heat to return to the room. But it should be remembered that the complicated design of the chimney can adversely affect draft, so do not get carried away with excessive bends.
Sometimes metal wings are welded to the body of the stove, for example, made of a corner or any suitable strip of metal. If the dimensions of the stove allow, you can weld a horizontal sheet of metal on top and make an additional hole in it not for a chimney, but for a pot or teapot.
The hole is closed with a special compound cover of several concentric circles. By removing or adding circles, you can adjust the degree of heating.
Another option for upgrading a potbelly stove is a brick case. Masonry is performed around the stove, while leaving a small gap between the metal body and the brick. The brick will absorb some of the thermal energy, and then gradually give it to the surrounding air.
If you wrap the chimney with a metal mesh and put stones in the formed gap, you can increase the heating efficiency. Even after the wood burns out, the stones will give off heat for some more time.
An alternative version of such a modernization is a metal mesh around the chimney, in which pieces of brick or stone are laid. This is a popular solution for stoves installed in the bath, a variation of the stove. But it should be remembered that only river “naked” fish of a uniform color and without inclusions are suitable for this. If a stone consists of layers of different types, it can burst under the influence of high temperatures.
If you need a furnace of solid size, the master has two gas cylinders at his disposal, you can combine them into one design. One of them is installed horizontally, and the second is placed vertically as a pipe for a chimney. The heating area is increasing, such a stove will work more efficiently.
The metal pipes built into the potbelly stove case in combination with a fan allow to increase the heating rate of the room, but to achieve this effect, electricity will be required
Finally, you can insert into the upper part of the pipe body through which air will circulate. If you put a fan at the end of these pipes, the air will move faster. Such an equivalent fan heater will allow you to warm up the entire room in a few minutes and more efficiently distribute thermal energy.
Here are recommendations for safely disassembling an old gas cylinder:
This video tells about the manufacturing procedure of a gas cylinder stove:
An original potbelly stove with the function of pyrolysis afterburning of fuel can be made of two gas cylinders:
A potbelly stove is a simple device that is not difficult to build and can be used quite widely. If the order of work is thought out in advance and correctly performed, such a stove can last quite a long time.
Please write comments on the article, ask questions, share your experience, if you already had to collect a potbelly stove from improvised materials.