To account for the used water in apartments and private houses, special devices are installed. By transmitting the readings at a certain time, control over the consumed resource is carried out, and then its payment.
In this material we will analyze in detail how to take the readings of the water meter, not to make mistakes in the calculations and to transfer the data to the supplier company in time.
Advantages of installing water meters
And first, let's see if it makes sense to install metering devices - some tenants still pay utility bills at common rates.
If you installed the counters and doubt that you did it right, just compare your payments with the receipts of the neighbors who are still pulling with the installation. The amounts indicated in the payment column are the best argument in your favor. They are approximately 1.5-2 times lower than those declared by residents who have not yet installed water meters.
Also thinking about the purchase and installation of metering devices? We recommend that you familiarize yourself with the procedure and rules for installing meters.
According to statistics, today more than 90% of Russians have already installed cold / hot water meters. The main reason for their use is saving water, respectively, and money for paying for a communal apartment
In the same receipts you can find the amount of resource consumed and wonder how much water we spend.
It is estimated that a monthly average resident of a comfortable city apartment performs the following actions:
- 118 times flush the toilet;
- 107 times uses a sink;
- Takes a shower 25 times;
- 4 times washed in the bathroom;
- Washes dishes 95 times.
As a result, he spends about 2-4 m³ of cold water and 1-3 m³ of hot water. Given that in families more often from 2 or more people, the amounts obtained are impressive. And this - if you take readings from the meters, without them you have to give even more money.
If we analyze all the nuances of payment with and without devices, then we can conclude that the installation of water meters brings only pluses:
- it is possible to control the spent cubic meters;
- easy to save family budget;
- no need to pay if you have been absent for a long time, as well as prove your absence;
- no need to pay the debts of irresponsible neighbors and pay interest for the increasing ratio.
And one more plus related to the protection of nature in general and the conservation of water resources in particular. Knowing your monthly expenses for water supply, you can learn to be more careful with water and gradually reduce consumption - within reasonable limits, of course.
How to take readings?
In order to pay regularly for the used water, it is necessary to perform a kind of “ritual” every month, on the same dates, including the following:
- receipt of receipt;
- taking readings from metering devices;
- entering data into the receipt (when transferring information by phone or the Internet, this item is not needed);
- payment of the actually used amount.
Depending on who is involved in generating utility bills, there are various ways to transfer data. But first things first.
Analysis of the design of the water meter
To understand how to correctly take readings from the meter on the water, you need to understand its design, or rather, examine the scoreboard - the top panel, covered with transparent plastic.
The main element that you have to “work with" every month is a digital scale, the same as that of an electric meter. Almost all tachometric instruments are equipped with a roller scale - the most popular due to their simple design, accuracy and low cost.
The main elements located on the front side of the meter. In addition to changing scales and indicators, the panel indicates the requirements for the characteristics of the supplied water - temperature, pressure
In addition to mechanical models, there are electronic ones in which the roller scale is replaced by a display. They are more expensive than conventional models, moreover, they are volatile - more often they work from a battery.
We talked more about the types of water meters and the rules for their choice in this article.
Before taking readings, you need to determine exactly which meter is installed on the pipe with hot water, and which - with cold.
There are several ways to find out:
- use color coding - the case of counters for cold water is usually painted blue (like the border of the display), for hot - in red;
- find lettering - domestic hot water / cold water or hot water / hot water;
- touch the pipe - the hot water main is always warm (except for periods of summer shutdown);
- open the tap and determine by the rotating indicator.
Traditionally, hot water pipes are laid from above, therefore, dhw meters are installed in the upper position. Unfortunately, not all plumbers comply with generally accepted requirements, therefore, when using this method of determination, you can make a mistake.
If both installed devices are red (and this is permissible, since the meters for domestic hot water can be installed on the hot water supply but not vice versa), you do not need to rely on color and letter marking to determine the type of meter, use other methods
For convenient reading, water meters must be installed in the field of visibility - in an open area of the water supply or under the cover of the plumbing hatch. Both devices must face the light source.
What numbers matter for the calculation?
Having decided on the belonging of the devices to hot and cold water supply, it is necessary to write down the actual numbers - those that are indicated on the scale or display. And before that, you will have to figure out which numbers need to be read on both water meters, and which ones should not be taken into account.
The scale of a simple tachometer instrument includes 8 rollers, that is, it shows 8 digits: the three rightmost ones indicate consumed liters, the rest - cubic meters.
Common tachometric models have an 8-digit scale, which is easiest to navigate by: we write off only black numbers, red ones are ignored!
However, there are counters whose scoreboard differs by the total number of digits or the number of digits after the decimal point. In this case, you should consult a specialist installing the meters, or a representative of the service company making the seal.
Is it possible to round off the readings? This is allowed, in the direction of increase or decrease. Usually, if the red numbers reach the value of "600", the number is increased by 1, that is, liters are rounded to the cube.
Reading example:
Suppose that the following number is on the dial of the HVS counter - 00076,268. We only write “76” to the receipt. Suppose that next month the testimony is 00084,896. We round and write in the column of the last month “76”, the current - “85”. The difference is 9 m³.
To understand how much you need to pay for the consumed water, we multiply the cubic meters spent by the regional tariff, suppose 34.5 rubles / m³. It turns out 310.50 rubles - so much will have to pay for cold water.
Using the same principle, you can calculate the amount to pay for hot water. If you add both amounts, you will receive a total payment for water - but excluding heating and sanitation, these are separate consumption items
We analyzed the specifics of calculating the water flow rate in another article of ours. Having figured out what numbers to submit on the water meters, it remains to choose the most convenient transmission method, if there are several.
Methods and time frames for transmitting testimony
Thanks to the development of communication networks, users are provided with many ways to transfer monthly water metering data.
All methods can conditionally be divided into 3 large categories:
- telephone message;
- transmission of testimonies on the Internet;
- supply of data on paper - receipts.
But first you need to understand where to send the testimony: to the management company, housing department, the main entrance or directly to the branch of the supplier company. It is better to check this information with the representative of the service organization.
You also need to know exactly what to transmit: meter readings or a self-calculated payment amount. The first option is often practiced - for accounting and control of the consumption process by specialists
Popular ways to save time:
Image Gallery
Photo from
Call to UK or Gorvodokanal
Data transfer through public services
Group or website of the management company
To transfer the meter readings in the listed ways, it is not necessary to make calculations - usually only the current readings are required to be transmitted, in some cases along with the data for the last month.
It is also convenient when data is collected in a special box installed in the entrance. To do this, fill out a receipt, the form of which was developed by the supplier or service organization. Further transfer is carried out by the responsible person
The most inconvenient way is to walk to the nearest branch of the Gorvodokanal. But older people often choose it, to once again go out and chat with people.
Dates of data transmission in different regions differ. Usually these are numbers from the 23rd to the 25th or 26th of each month. The exception is pre-holiday days, for example, before the New Year, the period can move for the period from December 19 to December 22.
The recommended period for the transmission of testimony is indicated on receipts.
Recommendations for reducing water consumption
Utility payments significantly devastate the family budget, especially in winter, when you also have to pay for heating. To reduce the amount, you can save on paying for water supply services by lowering water consumption, as well as reduce heating bills by installing a heating meter. But how to reduce water consumption?
The numbers on the counter will be lower if you follow the following recommendations:
Image Gallery
Photo from
Shower instead of bath
Dishwasher as a handmade replacement
Washing machine - an alternative to hand washing
Plumbing fixtures with different operating modes
Buying drinking water, you will reduce the consumption of tap water by about 40-60 liters per month per person. True, it will not be possible to save on this, but health can be improved.
Do not lose sight of such “trifles” as lime or rust smudges in the toilet bowl or sink. They signal regular leaks.
Make sure that the pipes, faucets, toilet bowl are always working. If you can not cope with the repair of plumbing fixtures yourself, feel free to call the master
Even in a small apartment, at least 2 taps are installed, in the kitchen and in the bathroom, and a toilet. If they leak, then the monthly volume of wasted water will necessarily affect the payment for a communal apartment.
We looked at more ways to reduce water consumption in the next article.
If there are still no water meters installed in the apartment, you are guaranteed to overpay. Fix this problem immediately! Step-by-step instruction on the installation of metering devices we have given here.
The user shares his personal experience:
Option to fill out a receipt:
Already there is experience in using “smart meters” - electronic devices that transmit readings directly to the user's phone or computer specialist from the service company.
It is possible that in the near future all homeowners will be relieved of the obligation to provide monthly water metering data, for which automatic devices will do this.
You still have questions about taking and transmitting readings of a meter for consumption of cold and hot water? Ask them under this article - other site visitors and our experts will try to clarify incomprehensible points to you.
If you have a smart meter installed that automatically transmits readings to a service company, please share your impressions of its use, add a photo of your device.