The trunk and equipment of a private water source tend to wear out gradually. To restore the technical condition, it is not necessary to resort to the services of hired workers, the owner of the development can do the repair of the well with his own hands. But first, you should familiarize yourself with the ways of resuscitation of the source. Is it true?
Here you will find valuable recommendations and a description of important nuances that ensure success in correcting the state of development. We described in detail the options for repair work and the technology for their implementation. The basis for the information presented by us is construction standards and the experience of owners of sections with wells.
The article thoroughly examined all sorts of reasons for violations in the work of an autonomous water intake structure. Describes how to clean the source and describes the method of replacing the casing. As excellently illustrating the theme of add-ons, photos and video applications are given.
Signs and preconditions for repair
The owner of the water well must constantly monitor the health of the source. This is in his interests, because the sooner a failure is detected and corrected, the cheaper and easier the repair will be. Sometimes timely cleaning is enough to ensure that the hydraulic structure works normally again, and the problem does not worsen.
It is worthwhile to deal with the diagnosis of breakdowns and troubleshooting if the water quality has deteriorated or the productivity of the well has decreased. As for changes in water quality, they are best seen by the results of chemical and microbiological analyzes.
A water well is a complex hydraulic structure in which both technical devices and hydrogeological elements participate. Symptoms for an upcoming repair may be a malfunction in the operation of both components
Decrease in productivity becomes obvious when water ceases to be enough for usual needs or it disappears altogether.
Water quality change
Ideally, every owner of any hydraulic structure should regularly take water samples to a local laboratory to determine its suitability. However, in practice, few people closely monitor the wells, so you have to rely on a subjective assessment.
Changes in water should alert:
- turbidity;
- the appearance of sediment during sedimentation;
- taste change;
- the appearance of an odor.
A reddish precipitate and an unpleasant aftertaste may indicate an increased iron content. Most often, the problem is not in the well itself, but in the erosion of iron-containing rocks by water. In this case, it is not necessary to repair the structure, it is enough to install filters with deferrizing cartridges.
If the water becomes cloudy and has a putrid odor, then the problem may be in bacteriological contamination. Water can not be drunk, and even more so given to children until the well is cleaned.
After cleaning, it will be necessary to pass a sample for analysis in order to obtain confirmation from laboratory specialists that the water is suitable for drinking and safe for health.
The underground water produced by the well is usually transparent and does not contain visually detectable inclusions. However, when the trunk is depressurized, particles of overlying incoherent soil layers may enter the mine. As a result, the pumped water acquires a color, sometimes even an unpleasant odor.
Well productivity decline
A decrease in well productivity can occur gradually or dramatically.
There may be several reasons for this:
- Clogging. As a rule, owners of sand wells face such a problem. Artesian springs usually do not silt. Particulate matter first gets into the primary filters, and later into fine filters. A decrease in well production occurs gradually. In this case, you need to clean the structure.
- Malfunctions in the pump. Eternal technology does not exist, and pumping equipment breaks down in the same way and requires replacement. In some cases, cleaning the device and preventative maintenance are sufficient, and sometimes you have to buy a new pump. If the productivity of the well has decreased, the pump should be examined first.
- Casing pipe wear. If malfunctions in the operation of the well arose a few years after construction, then the problem may be in the pipes. They rust over time. The lower the quality of the materials of which the production casing is made, the earlier it is necessary to repair the structure. Often due to rust, leaks occur at the joints of pipes.
- Errors of design and installation of the well. If initially the source is poorly arranged, then it will be very difficult to establish its work. It is worth contacting professional drillers to understand why difficulties arose and to solve the problem. Often the only reasonable way out of the situation is the construction of a new well.
It is very important for future trouble-free operation to properly equip a water source immediately after drilling. It is necessary to protect the mouth of the mine with a head or arrange a caisson for servicing and placing equipment, install a filter and lay a pipeline taking into account construction requirements.
It is worth noting that sometimes a drop in water level in an aquifer simply happens. It is understood that as a result of prolonged operation of the water supply source, the water supply may be reduced.
It is impossible to influence this, but you can contact the company engaged in drilling in the area, consult with specialists on how to solve the problem.
In a dry period, the water level in the “sand” water intake can change. If we are talking about a shallow source, this may be due to seasonal phenomena. Then, during a period of heavy rainfall, the water returns. If the flow rate has significantly decreased in the limestone well, you will probably have to build a new structure
Flushing as a breakdown prevention
Often you can find a recommendation to flush the well to prevent siltation. Usually such advice is given by drilling specialists. Many well owners have a suspicion that they are simply tied to a certain company, which will deal with their water supply system after the arrangement.
Are preventative flushes really necessary or is it still a trick? If the well works continuously, then there is no particular need for such an event. But for a structure that is used only seasonally or temporarily, it is advisable to periodically wash to avoid sand and silt settling.
Sometimes regular flushing can actually prevent well repair or restoration, but more often than not, they are not needed. Extra flushing will not hinder in case of difficulties with putting the well into operation after construction or a long downtime.
If the well is built in the country and is used only during the summer season, it must be washed before operation and closed for the winter with the onset of cold weather
Subtleties of diagnosis
To eliminate the breakdown, you need to clearly understand its cause. If you plan to repair the well yourself, if the diagnosis is incorrect, the owner will lose only time. If he turns to professionals, then also money. Therefore, you should not rush and carefully consider the diagnosis.
First of all, you need to make sure that the problem is really in the hydraulic structure itself, and not in the water distribution system. To do this, the pump is disconnected from the water supply, connected to a conventional hose and put into operation.
If the water comes with good pressure, then everything is normal with the well and pumping equipment. The source of trouble should be sought in the water distribution system. If the pressure is weak or the water does not flow at all, and the pump is idling, you really need to do the resuscitation of the well with your own hands or call specialists.
To check the pump, you will have to get it and temporarily connect another. If no changes occur, equipment failure can be ruled out. In this case, you will have to clean the well or deal with malfunctions of the production casing.
In case of suspected breakdown of the submersible pump, it is removed from the well and another unit is installed instead. If it is better to pump, then the reason for the violations in the pump
In the case of self-diagnosis, it is necessary to act by the method of exclusion, checking each node in turn. The study of the borehole of the special equipment is impossible, you will have to call the employees of the drilling company.
In order to clean the well, filter or replace the production pipe, you should also resort to the help of drillers. If it is simply silty, then it is possible to restore performance. In serious cases, you should hire professionals. And even in this case there is no full guarantee that the well productivity will be restored.
Four ways to clean a well
If during the diagnosis it turned out that the problems arose due to siltation, then the well can be cleaned independently. To do this, it is washed with water or purged with a compressor.
The easiest option is to pump with water. The process requires considerable time and effort, but the result is worth it. If the filter is not destroyed, but simply dirty, then it is entirely possible to completely restore the source's productivity.
During the washing process, a large amount of dirty water is poured. It is advisable to immediately choose a place for its discharge, otherwise the site or closely located outbuildings may be flooded
Method # 1 - flushing with a pump
Have to stock up on clean water in advance. If your own well does not work well, this can become a problem, you will need to turn to neighbors for help. Water will require a large tank and a pump, and finding them can also be difficult.
If these issues are resolved, then you can begin to work. The hose is connected to the pump and lowered to the bottom of the well. It is important that he gets not just to the mirror of water, but almost to the bottom.
The pump is turned on to pump water, and it raises sludge and sand from the filter. The wellbore quickly overflows with water, and it begins to gush uncontrollably. Particles of contaminants are released along with water.
[the_ad_placement id = ”mobile-vstavka-v-tekste-5“]
This is one of the fastest and most reliable ways to clean a silty source. If you can’t do it yourself, you can turn to hydrogeologists and cesspool workers. The former will calculate the necessary hydraulic shock power, while the latter will help with a large volume tank for the removal of excess water.
Image Gallery
Photo from
Flushing - preparing the well for operation
Removing sand and sludge from a mine
Sump for draining water from the site
Clean water as a result of flushing
Method # 2 - cleaning with a vibrating pump
A shallow well can be cleaned of sludge and sand using a vibration pump. Often use small-diameter equipment, for example, devices of the brand "Kid". The pump is lowered into the shaft of the mine to the level of the filter, turn on and carefully swing the well.
The device will pick up solid particles and they will come to the surface with water. Such a flushing of the well may take several days, but it will be effective only if light contamination.
During well cleaning, the working parts of the pump may become clogged with dirt and the motor may overheat. Therefore, it is advisable to take breaks and clean the device from contamination.
The advantage of this method is its simplicity and cheapness. You can do everything yourself, no complicated equipment is required.
When cleaning the well, it is necessary to raise and lower the vibration pump to shake the sludge and sand. The flow of water tears particles from the filter, the walls of the shaft, after which they enter the pump
Method # 3 - use a bailer
This method is suitable only for shallow wells - not more than 30 m. To work, you will need helpers, a winch and a drill - a chipper. It is a piece of metal pipe with the upper part closed by a net and a bottom washer. The bailer is attached to a long, durable cable.
This simple device is used to clean a silted well. It can be bought at a specialty store or made manually.
The device is lowered to the very bottom of the well, after which it is raised by about half a meter and again sharply lowered. After several such manipulations, the bailer is removed from the well and cleaned of sand. Usually it gets about 0.5 kg.
Not all well owners consider this method of cleaning effective, but most nevertheless agree that the bailer helps to cope with siltation. The main advantage of cleaning using a bailer is low cost. If you make the device yourself, you can remove the sand almost for free.
To make it easier to break the cohesive rock (loam / clay / sandy loam), there may be tines in the lower part of the chaff. They crash into a plasticine-like mass, separating it from the massif of the formation. To extract the destroyed cohesive rock, the bellow is changed to a glass. So they drill if it is necessary to deepen the wellbore due to a greatly reduced production rate
Method # 4 - flushing with two pumps
The method is similar to flushing with a pump, but has some differences. Two pumps are required - submersible and surface. Not far from the well, a volumetric water tank (from 200 cubic meters) should be installed, and in it - a home-made filter made of a bucket with a net or a female stocking. A hole is made at the side and bottom of the tank through which water will be pumped using a surface pump.
Using a deep pump, contaminated water is pumped into the tank, passing through a filter. The surface pump draws purified water from the reservoir and re-injects it into the well. The bucket is periodically freed from sand and silt. The procedure is carried out until clean water without impurities flows from the well.
There are many ways to clean a silty well. When choosing the right one, it is worth remembering that the method should not only be cheap and convenient, but also safe for other elements of the structure
Production string replacement
One of the most unpleasant breakdowns is wear of the production pipe. Its replacement is a complex and time-consuming process requiring considerable financial investments. It is best to entrust the work to professional drillers. For self-fulfillment, it is desirable to have the appropriate skills, as replacing a borehole pipe is even more difficult than installing a new one while drilling a well.
It is easiest to work if the casing and production structures consist of two pipes of different diameters. In this case, only the production pipe is changed without touching the casing. If everything is done carefully, the well’s performance will be restored.
It is better not even to start repairing the well with asbestos-cement pipes, as material is destroyed under additional loads.This is the case when it is worth immediately starting the construction of a new hydraulic structure. But the metal pipe is quite possible to replace, even if the material is very rusty.
Image Gallery
Photo from
Well Casing Replacement
Retractable barrel clamp
Loop for pulling the pipe from the barrel
Upper Casing Excavation
To dismantle the pipe, it is gripped with a loop or a special clamp and pulled out using any available lifting mechanism - a railway jack, a truck crane, etc. The main thing is that the device provides the necessary strength for lifting.
When the pipe is removed from the shaft, install a new one - metal or plastic. Do not use asbestos cement. Material is impractical and potentially hazardous to health. This is confirmed by data from the World Health Organization.
New pipes can be connected using threads or nipples. You should choose high-quality connecting elements with a special anti-corrosion coating. If plastic pipes are selected, a durable, non-nipple connection is provided here. When choosing pipes, do not save. This is fraught with new breakdowns.
When replacing the production casing, a new pipe is selected, focusing on the depth of the well, future loads, durability of the material, its resistance to chemicals
Important downhole filter information
When cleaning the well, it is important to be careful, otherwise you can accidentally destroy the filter, especially if a water hammer is used. If cleaning the filter with chemicals was used, then the quality of the water will inevitably deteriorate. Do not worry. This is a temporary phenomenon.
Gradually, the well will be cleaned of chemistry, and the water will again become quality. So that the reagents do not have a negative impact on health, you should pump water from the well for 12 hours and for a couple of days abandon its use for domestic purposes. You also need to put good filters in the house and not use unfiltered water for drinking and cooking until it is clean.
When dry cleaning the downhole filter, substances are used that are used in the food industry, therefore it is generally believed that they are safe. However, you should always remember the quantity. The concentration of chemistry in the water after cleaning is too high. Reasonable precautions must be taken to prevent poisoning.
The initial purification of ground water from mineral particles produces a downhole filter. It settles down over the entire thickness of the aquifer plus half a meter above and below (+)
In addition to chemical cleaning of the filter, you can use mechanical. This method is safe and does not affect water quality. To clean the filter from deposits, use a metal device that looks like a normal brush for washing bottles, but much larger.
At the same time as the ruff, you can use cleaning using water injection. But you should always remember the risks. The filter may not withstand the extra pressure and may break. Better not to experiment without extreme need.
Video # 1. Demonstration of siltation of a well and presentation of its pumping process on its own:
Video # 2. How to clean a well with the help of the simplest home-made chipper:
Unfortunately, you can never be sure that after recovery, the well will work fully and smoothly.
There are cases when resuscitation of a well is impossible at all, especially if it is placed on sand and the filter is not removable. Then it’s easier to arrange a new source than to bring the old one back to life, because in the end, the forces and means for this will be spent about the same.
If there are problems with a new well, it means that it was originally constructed incorrectly.The contract with the driller company usually indicates the warranty period, so it is possible to have its employees determine the cause of the malfunction and eliminate it, if possible.
Problems with the pump, filter, siltation - this is solved. But replacing a completely destroyed filter or worn trunk pipes will lead to serious costs with an uncertain result. Here it is necessary to decide what is more profitable - restoration of the old well or construction of a new one.
Tell us about your own experience gained during the restoration of the well, share only the nuances of work known to you. Please write comments in the block below. Ask questions, post a photo on the topic of the article.